Ak47 Part 11 Drill And Pin The Barrel Trigger Guard Install
![Poster 12 X18 Russian ak 47 Kalashnikov Rifle Manual Exploded Parts Poster 12 X18 Russian ak 47 Kalashnikov Rifle Manual Exploded Parts](https://s-media-cache-ak0.pinimg.com/originals/a8/f7/16/a8f716ac4b1f1f9c868e3786946014e3.jpg)
Poster 12 X18 Russian Ak 47 Kalashnikov Rifle Manual Exploded Parts In this video i drill and pin the barrel and then install the trigger guard, also do a little furniture fitting. 1 4 inch end mill followed with 7mm reamer and pin it. works every time. best to use a good drill press and vice or mill to cut with the end mill from both sides carefully then ream with a good hand drill with lots of cutting oil. never reverse the reamer.
![M M Industries ak47 Ak74 M10x Rivetless trigger guard Assembly Us M M Industries ak47 Ak74 M10x Rivetless trigger guard Assembly Us](https://cogunsales.com/wp-content/uploads/2023/07/Trigger-Guard-1.png)
M M Industries Ak47 Ak74 M10x Rivetless Trigger Guard Assembly Us After i double and triple checked that my headspace was correct, i aligned and clamped the trunnions in my drill press and used a 4 flute mill bit to slowly and carefully bore the pin holes from each side. i then used a 7mm reamer to clean the holes through from one side. make sure the trunnion is aligned under the mill or reamer, make sure the. Uard comes preassembled to install in your lowerinsert the tr. gger guard into the lower as shown in figure 1. with the holes in the guard and lower lined. up lightly tap the roll pin through until flush. a li. t oil on the hole might assist in the assembly.with the pin inserted move to the front of the trigger guard and locate. Drill trunion holes in rcvr (if applicable). fit install trigger guard, trunions. press and headspace barrel. fit install internals, furnature, required us parts and any other fitting tweaking (mag well, carrier rails, extractor tuning, safety fit, etc) test fire to confirm function (30 rounds minimum). $195.00. Press out the barrel pin and press out barrel from trunnion. rivet both trunnions and trigger guard. press in barrel assembly and line up the barrel pin hole, then just press in the barrel pin. getting a pre headspaced kit was definitely the way to go with this, it takes out a lot of the work.
![How To Upgrade An ak 47 trigger Hunting Retailer How To Upgrade An ak 47 trigger Hunting Retailer](https://www.huntingretailer.com/uploads/images/PR_FTC_Press-the-trigger-holding-the-hammer-to-release-e1457542125376_190104_101515.jpg)
How To Upgrade An Ak 47 Trigger Hunting Retailer Drill trunion holes in rcvr (if applicable). fit install trigger guard, trunions. press and headspace barrel. fit install internals, furnature, required us parts and any other fitting tweaking (mag well, carrier rails, extractor tuning, safety fit, etc) test fire to confirm function (30 rounds minimum). $195.00. Press out the barrel pin and press out barrel from trunnion. rivet both trunnions and trigger guard. press in barrel assembly and line up the barrel pin hole, then just press in the barrel pin. getting a pre headspaced kit was definitely the way to go with this, it takes out a lot of the work. The sheet metal trigger guard is secured to the bottom of the receiver with five rivets, two on each side of the magazine release and one in front of the trigger opening. the five rivet holes were. The ak trigger guard riveting jig makes this task simple and straightforward. if you’re trying to rivet the trigger guard onto a receiver that already has the rails welded in and the center post installed, like mine, the kit even comes with the extra post and plate for that. ak builder barrel press kit. 4.) barrel press kit.
Comments are closed.