Ak47 Pin Removal Without A Press Part 3
![ak47 Pin Removal Without A Press Part 3 Youtube ak47 Pin Removal Without A Press Part 3 Youtube](https://ytimg.googleusercontent.com/vi/ujykBpldwlY/maxresdefault.jpg)
Ak47 Pin Removal Without A Press Part 3 Youtube Removing barrel pins from an ak47. some are easy, some are not. share the video and subscribe!. Removing barrel pins from an ak47. some are easy, some are not. share the video and subscribe!.
![ak47 Ak47gn Fix Stock Poland Deactivated Assault Rifle without ak47 Ak47gn Fix Stock Poland Deactivated Assault Rifle without](https://www.zib-militaria.de/WebRoot/Store8/Shops/61431412/53B6/A8F8/3321/2F3E/DEAB/C0A8/2BBC/BA1C/0710.jpg)
Ak47 Ak47gn Fix Stock Poland Deactivated Assault Rifle Without Re: firing pin removal. okay i decided to try the drill bit punch method. it worked! took a 5 64" bit, broke off the bit part, leaving a shank just over 1". ground the broken tip flat and slightly chamfered the edge. turned the bolt upside down on my vise with a gap for the drift pin to pass. held the 5 64" punch with a needle nose vise grip. Reactions. 29. jun 2, 2010. #8. hammer and punch.drill a hole into a block of 2x4 for the pin to pass through and lay the barrel pin over the hole and whack the pin with the punch.use a short stubby punch that is slightly smaller than the pin.this keeps the punch from breaking.try taping the barrel receiver stub to the wood to keep it in place. Strip the receiver and take off your front sight. heat the front trunnion up to about 400 500 degrees f. lay the front trunnion on something hard and drive the barrel pin out with a hammer and punch. while still hot take the front trunnion over to a vice and support the front trunnion with the barrel pointing down. I've got the hf 20 ton press and the 1.6" akb barrel kit works just fine. just get the 20 ton and don't go full monkey when pressing stuff and you'll be fine. 1. i have a wbp headspaced kit that has most of the barrel pin removed. i would like to know if there is a method to remove it without a press or if the….
![ak47 pin removal without a Press part 1 Youtube ak47 pin removal without a Press part 1 Youtube](https://ytimg.googleusercontent.com/vi/kLVT0naU6GM/maxresdefault.jpg)
Ak47 Pin Removal Without A Press Part 1 Youtube Strip the receiver and take off your front sight. heat the front trunnion up to about 400 500 degrees f. lay the front trunnion on something hard and drive the barrel pin out with a hammer and punch. while still hot take the front trunnion over to a vice and support the front trunnion with the barrel pointing down. I've got the hf 20 ton press and the 1.6" akb barrel kit works just fine. just get the 20 ton and don't go full monkey when pressing stuff and you'll be fine. 1. i have a wbp headspaced kit that has most of the barrel pin removed. i would like to know if there is a method to remove it without a press or if the…. Option 1: use a hydraulic shop press. this is definitely a proven method. 12 20 ton shop presses were traditionally the go to tools for a lot of ak work relating to barrels and rivets. for barrel work, guys use jigs from ak builder and others plus can make their own. For aks there is multiple thread patterns. 14x1 is one as is 24x1.5 among a couple others. if they are needing a brake device to put something ontop for their suppressor its an unique design & if you consider the detent pin gets stuck in such a way critically that you need to jimmy it out in very hard uncomfortable ways, its 100% their design being crap and not you.
Comments are closed.