Building A Koi Pond Your Step By Step Guide The Goodhart Group
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Place the lining into the hole, making sure that you allow the liner to lay on top of all of the curves in the pond. install the different systems you purchased for your pond before you add the water. once that is completed, add in the water. the water to koi ratio should be between 150 to 200 gallons for each fish. The design is simple, 4″ x 4″ x 8′ posts on all four corners and one additional post in the middle of each 12′ side for a total of six posts. dig each post hole 18″ down by 12″ wide from the bottom of the pond excavation. set the 4″ x 4″ posts in the holes and fill with concrete – just like setting fence posts.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
1. fill the pond with a garden hose and dechlorinate the water. place the end of the hose in the bottom of the pond, then turn on the tap and let the pond fill to about 1–2 in (2.5–5.1 cm) below the rim. if you live in an area with non potable water, use a hose filter to purify the water as it comes out. Step 4. you need to use underlayment and lay it down on the entire pond and fall area and thereafter, use a 45 mil epdm liner. the liner should extend beyond the limits of the pond by at least 1 ft to allow for rockery over winter and settling earth. to prevent the liner from escaping from its position, extend it behind the waterfall as well. Unfold the epdm liner and fit it to match the shape of the pond. extend the liner onto the banks for a minimum one foot distance. install the underlayment first, followed by the pond liner. fold the corners inward and leave at least 12 inches over the side walls of the pond to secure it with a cap board or stone. 10 steps to build a pond. step 1: plan ahead. pond placement is key: steer clear of trees with heavy root systems & electrical lines; look for an area with either part sun or full sun if you are planning to keep fish and or plants. step 2: excavate.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Unfold the epdm liner and fit it to match the shape of the pond. extend the liner onto the banks for a minimum one foot distance. install the underlayment first, followed by the pond liner. fold the corners inward and leave at least 12 inches over the side walls of the pond to secure it with a cap board or stone. 10 steps to build a pond. step 1: plan ahead. pond placement is key: steer clear of trees with heavy root systems & electrical lines; look for an area with either part sun or full sun if you are planning to keep fish and or plants. step 2: excavate. Myth 2. koi ponds need to be large. '''a general rule of thumb is one inch of fish per 10 gallons of water.''' you can make a pond any size but you do have to be careful of over crowding in smaller ponds. i often heard people say koi only grow to a certain size based on how large your pond is. A koi pond can have a bit of debris build up if the pond isn't properly constructed. although we have step by step instructions on how to build a pond, there are some other helpful tips to know on keeping it clean. it's ideal to have a drain installed in your koi pond. this would ideally be connected to your skimmer where your pump would be.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Myth 2. koi ponds need to be large. '''a general rule of thumb is one inch of fish per 10 gallons of water.''' you can make a pond any size but you do have to be careful of over crowding in smaller ponds. i often heard people say koi only grow to a certain size based on how large your pond is. A koi pond can have a bit of debris build up if the pond isn't properly constructed. although we have step by step instructions on how to build a pond, there are some other helpful tips to know on keeping it clean. it's ideal to have a drain installed in your koi pond. this would ideally be connected to your skimmer where your pump would be.
Comments are closed.