Changing M54 Heater Coolant Hose Without Removing The Intake Manifold
Changing M54 Heater Coolant Hose Without Removing The Intake Manifold Some hoses going to heater core all gaskets (intake, icv), o rings (for fuel injector), since it is removed during the intake manifold removal vacuum lines ofhg coolant sensor (since it had more than 100k on it) cvv and its hoses 2) cleaned the alternator vent throttle body side of the engine which was opened. one of the biggest projects i did. Hello guys.as the tittle says i want to replace the coolant pipe under the intake manifold without removing the manifold.i dont want to remove the intake manifold because i did that last summer, but the ****in seal of the heater pipe is leaking badly i dont know why since i replaced it while changing the ccv and intake manifold gasket.if i remove the oil filter housing can access the bolt of.
![2017 Gmc Acadia 3 6l V6 coolant Temp Sensor Installation Easy 2017 Gmc Acadia 3 6l V6 coolant Temp Sensor Installation Easy](https://ytimg.googleusercontent.com/vi/4PQpRjtCvRA/maxresdefault.jpg)
2017 Gmc Acadia 3 6l V6 Coolant Temp Sensor Installation Easy 4. spend the money on a smoke tester and really thoroughly check for vac leaks when you’re done. 5. do the ccv system. not too expensive and easy with the intake off the engine. this is an older thread, you may not receive a response, and could be reviving an old thread. please consider creating a new thread. Took sometime this week to replace my ccv system and the two plastic coolant hoses under the intake manifold as well as manifold tb gaskets. after removing the intake mani, saw the two hoses and to be honest they looked to be in good condition. was trying to find any excuse to not. change them out, but decided to pull them out anyways as the. Remove maf connection, boots and vacuum lines. 4. disconnect upper ccv tube, vanos connector, air temp connector, disa connector, idle control valve connector, purge valve connector & hose, throttle body connector, rear im sap vacuum line. 5. remove 1 bolt, 2 nuts electrical bracket 10mm. In today's video, we replace the notorious m54 coolant lines under the intake manifold on a 2005 bmw x3 3.0 liter. this is a common issue among all m54 stra.
![How To Clean Diesel intake manifold without removing How To Clean Diesel intake manifold without removing](https://cleanstuffeasy.com/wp-content/uploads/2022/12/How-to-Clean-Diesel-Intake-Manifold-Without-Removing.jpg)
How To Clean Diesel Intake Manifold Without Removing Remove maf connection, boots and vacuum lines. 4. disconnect upper ccv tube, vanos connector, air temp connector, disa connector, idle control valve connector, purge valve connector & hose, throttle body connector, rear im sap vacuum line. 5. remove 1 bolt, 2 nuts electrical bracket 10mm. In today's video, we replace the notorious m54 coolant lines under the intake manifold on a 2005 bmw x3 3.0 liter. this is a common issue among all m54 stra. 23. remove the intake manifold. (have pliers ready) when re installing the tightening torque is: intake manifold to cylinder head m7: 15 nm (11 ft lb) m8: 22 nm (16 ft lb) while removing, the coolant temp switch (wire located at the back portion of the fuel injector harness) will get hung up on the fuel line located on the back of the intake. Bmw x3 sport utility (2004 06) project time: 3 hours. tab: $150. talent. tools: set of sockets 10, 11, 13mm, screwdrivers. parts required: coolant pipes, engine coolant, intake gasket set. performance gain: car will cool down again or restore function of heater. complementary modification: change radiator hoses.
Comments are closed.