Drip Edge 01 Waterproofing Roofing Systems
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Search . drip edge 01. jpg pdf dwg. The liberty™ sbs self adhering roofing system was made to simplify a roofer's life when it comes to residential low slope roof applications. watch the cap sheet install demonstration and get pro tips about cap sheet priming, overlap allowance, end laps and t joints, and more in the above video.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Avoid damaging the shingles and underlying roofing felt. once removed, measure the length of the eave and cut the new drip edge to size, allowing for a 1 2 inch overlap at each joint for continuous water flow. before installation, check that the wood along the eaves is not rotted and replace any damaged sections. On the rakes, the drip edge goes over the membrane, so the roofers apply the membrane first. the drip edge is nailed in place using 1 1 2 galvanized roofing nails. a felt tip marker works great for marking cuts. and, again, prying open the end with a small flat bar allows the pieces to overlap cleanly. The most obvious attributes that distinguish a drip edge from a gutter apron are shape and material. a gutter apron has more of an l shaped whereas a drip edge is t shaped. a gutter apron also comes in metal strips featuring steel and aluminum sheets. drip edges are available in galvanized steel, aluminum, copper, and fiberglass materials. Some of the most common materials used in roof waterproofing include cementitious coatings, liquid membranes, bituminous coatings and membranes, polyurethane liquid membranes and epdm rubber. cementitious coatings are made from a mixture of cement and water resistant agents that create a hard surface when applied to the roof.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
The most obvious attributes that distinguish a drip edge from a gutter apron are shape and material. a gutter apron has more of an l shaped whereas a drip edge is t shaped. a gutter apron also comes in metal strips featuring steel and aluminum sheets. drip edges are available in galvanized steel, aluminum, copper, and fiberglass materials. Some of the most common materials used in roof waterproofing include cementitious coatings, liquid membranes, bituminous coatings and membranes, polyurethane liquid membranes and epdm rubber. cementitious coatings are made from a mixture of cement and water resistant agents that create a hard surface when applied to the roof. Step 1: start at the eaves: begin by placing the drip edge along the eaves of the roof, aligning it with the roof’s edge. make sure the drip edge extends slightly over the edge to direct water away. step 2: secure the drip edge: use roofing nails or screws to secure the drip edge in place. Both gutter aprons and drip edges work to serve the same purpose: to prevent roof damage. your home’s drip edge or gutter apron system helps protect your roof deck and attic from water damage that could be caused by water seeping into the fascia. this can increase the lifespan of your roof and ensure you get the most out of your roof.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Step 1: start at the eaves: begin by placing the drip edge along the eaves of the roof, aligning it with the roof’s edge. make sure the drip edge extends slightly over the edge to direct water away. step 2: secure the drip edge: use roofing nails or screws to secure the drip edge in place. Both gutter aprons and drip edges work to serve the same purpose: to prevent roof damage. your home’s drip edge or gutter apron system helps protect your roof deck and attic from water damage that could be caused by water seeping into the fascia. this can increase the lifespan of your roof and ensure you get the most out of your roof.
Comments are closed.