How To Build A Pergola Attached To House Pergolas How To Build And
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
A pergola that is attached to your house can be a great addition; it’s a good way to create a useful sheltered outdoor area and give you shade from the sun. Measure straight out from the mark to the patio edge and mark again. snap chalk lines between the marks at the house and the patio edge. pergola post layout (how to build a pergola attached to the house) measure back towards the house 8 to 12 inches from the patio edge along the chalk lines and mark. snap a new chalk line between these marks.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
I put a small patio in my backyard to support my hot tub but my backyard backs up to my neighbors and there was no privacy. i built this pergola attached to. An attached pergola hangs from a ledger board that is secured to the rim joist with lag screws or structural screws. to ensure that the ledger doesn’t allow water to reach the sheathing and foster rot, the siding is removed from the area (it will be patched back later), and a water resistive barrier (wrb) is applied over the exposed sheathing. Attach 2x6 and 2x4 cross beams. to attach the pergola to a building, you will screw joist hangers to the building. the 2x6 ‘s will fit in the joist hangers and then connect across to the posts. use structural wood screws to connect 2x4 's (these run perpendicular to the house) and 2x6s to posts. Take two 2 x 8 end beams and place them into the joist hangers or carve notch marks with a jigsaw to match the edge of the ledger beam. take an adjustable clamp and temporarily hold the end beams against the posts. check to make sure your support beams are level and adjust as needed. take a drill and pre drill holes.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Attach 2x6 and 2x4 cross beams. to attach the pergola to a building, you will screw joist hangers to the building. the 2x6 ‘s will fit in the joist hangers and then connect across to the posts. use structural wood screws to connect 2x4 's (these run perpendicular to the house) and 2x6s to posts. Take two 2 x 8 end beams and place them into the joist hangers or carve notch marks with a jigsaw to match the edge of the ledger beam. take an adjustable clamp and temporarily hold the end beams against the posts. check to make sure your support beams are level and adjust as needed. take a drill and pre drill holes. Install wood plugs in the pergola columns. family handyman. cut 5 1 2 in. round treated wood plugs to fit the inside of your columns. glue and screw together a pair for each column top, then glue the plugs flush into the top of each column. secure the plugs to the columns with 2 in. deck screws. Step 1 – installing the posts. the easiest way to build a freestanding pergola is to start with post holes. use an auger to dig two post holes per row, each hole 8’ apart. the depth of the holes should match regional building codes pertaining to the frost line. in most cases, that means 24” holes with a width of 9”.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Install wood plugs in the pergola columns. family handyman. cut 5 1 2 in. round treated wood plugs to fit the inside of your columns. glue and screw together a pair for each column top, then glue the plugs flush into the top of each column. secure the plugs to the columns with 2 in. deck screws. Step 1 – installing the posts. the easiest way to build a freestanding pergola is to start with post holes. use an auger to dig two post holes per row, each hole 8’ apart. the depth of the holes should match regional building codes pertaining to the frost line. in most cases, that means 24” holes with a width of 9”.
Comments are closed.