How To Fit A Backpack Backpacks Global
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
To determine the bottom of your torso, place your hands on either side of your waist, just above the pelvic bone. make sure that your index fingers are pointing to the front and your thumbs are pointing to the back. hold your hands steady and align your thumbs across your back to form an imaginary line. A 50l hiking backpack corresponds to a volume of 3,051.19 cubic inches. this size of backpack is designed specifically for people who hike long distances and is made of waterproof materials. the dimensions of a 50l backpack are approximately 29.5" x 13" x 10".
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Before you pour water into the pack, check your bladder for any leaks or holes that might allow water to escape. if there are any, use a patch or glue to fix it before proceeding. fill your hydration bladder with cold or lukewarm tap water – room temperature is best if you’re not strapped for time. Step 4: sternum strap. slide the sternum strap until it's at a comfortable height across your chest: roughly an inch below your collarbones. buckle and tighten the sternum strap to set the shoulder straps at a width that allows your arms to move freely. avoid the common mistake of overtightening the sternum strap. If the torso length is adjustable, take the pack off again and shorten the length. 8. tighten the load lifters to even the back panel of the pack out with your back. pull down on the tabs of the straps to tighten them until the straps make about a 45 degree angle down from the back panel of the backpack. Put on the pack: put on the pack and adjust the shoulder straps so that they sit comfortably on your shoulders. adjust the sternum strap so that it sits comfortably across your chest. adjust the hip belt: the hip belt should sit snugly on your hips, with the center of the belt over your belly button.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
If the torso length is adjustable, take the pack off again and shorten the length. 8. tighten the load lifters to even the back panel of the pack out with your back. pull down on the tabs of the straps to tighten them until the straps make about a 45 degree angle down from the back panel of the backpack. Put on the pack: put on the pack and adjust the shoulder straps so that they sit comfortably on your shoulders. adjust the sternum strap so that it sits comfortably across your chest. adjust the hip belt: the hip belt should sit snugly on your hips, with the center of the belt over your belly button. Reach back and pull on the load lifters straps so that the pack is at about a 45 degree angle from your body. 6. adjust the sternum strap. finally, buckle the sternum strap across your chest and tighten it so that it’s snug but again, not too tight. you have to be able to breathe when you’re hiking. Adjust your shoulder straps by pulling the webbing adjusters down and back until they fit snugly against your shoulders. ideally, the bottom of the shoulder strap should end around the midline of your side. adjust the load lifter straps next. these should be at a 30 to 45 degree angle for multi day packs or slightly less for day packs, pulling.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Reach back and pull on the load lifters straps so that the pack is at about a 45 degree angle from your body. 6. adjust the sternum strap. finally, buckle the sternum strap across your chest and tighten it so that it’s snug but again, not too tight. you have to be able to breathe when you’re hiking. Adjust your shoulder straps by pulling the webbing adjusters down and back until they fit snugly against your shoulders. ideally, the bottom of the shoulder strap should end around the midline of your side. adjust the load lifter straps next. these should be at a 30 to 45 degree angle for multi day packs or slightly less for day packs, pulling.
![](https://i0.wp.com/sicepat.com/images/image-not-found.png)
Comments are closed.