How To Fit Skirting Boards Step By Step Guide Checkatrade
![Putty And Paint Finishing Touches For A Perfect skirting Board Look Putty And Paint Finishing Touches For A Perfect skirting Board Look](https://www.checkatrade.com/blog/wp-content/uploads/2021/03/Feature-How-to-fit-skirting-boards.jpg)
Putty And Paint Finishing Touches For A Perfect Skirting Board Look Firstly, drill a small hole in your skirting board. remember to always screw at 600mm centres. next, use the drill to make a hole in the wall behind where your skirting board will sit. make sure these holes line up when the skirting is in place. you can now fit the rawl plug and screw the board to the wall. Step one: measure the board. take your skirting board and line it up along the wall it’s being attached to. mark the corner of the wall on the skirting board and draw a line with a pencil and ruler. top tip: don’t forget to mark which corner the skirting board is on using an arrow that faces inwards or outwards.
![how To Fit Skirting Boards Step By Step Guide Checkatrade how To Fit Skirting Boards Step By Step Guide Checkatrade](https://www.checkatrade.com/blog/wp-content/uploads/2021/03/Types-of-skirting-board-768x566.jpg)
How To Fit Skirting Boards Step By Step Guide Checkatrade The cost to install skirting boards can vary depending on the quality, material and size of the room they’re being fitted in. on average, you can expect carpenters to charge the cost of fitting skirting boards at a hourly rate of around £31.25. however, if you also need painting to be done, you’ll also need to factor in the average hourly. Partially insert an 8 gauge screw into a 6mm wall plug and push it into the pilot hole. tap the screw head with a hammer to force the plug through the board and into the wall. tighten the screw until the head sits below the board’s surface. repeat this process for all the remaining pencil marks. 2. screw the boards into the studs inside a plaster wall instead of using glue. find the studs in the plaster wall and mark their position on the wall and on the skirting board. drill a pilot hole into the board and countersink the hole with a larger drill bit. screw the boards into place. Here are the steps to follow: start by using a pry bar or chisel to gently loosen the skirting board from the wall. be careful not to damage the wall or the board itself. once the board is loosened, use a crowbar or similar tool to slowly pry it away from the wall. again, be careful not to damage anything.
![how To Fit skirting Board In Place how To Fit skirting Board In Place](https://www.sdgyoungleaders.org/wp-content/uploads/2022/02/fit-skirting-boards-8.jpg)
How To Fit Skirting Board In Place 2. screw the boards into the studs inside a plaster wall instead of using glue. find the studs in the plaster wall and mark their position on the wall and on the skirting board. drill a pilot hole into the board and countersink the hole with a larger drill bit. screw the boards into place. Here are the steps to follow: start by using a pry bar or chisel to gently loosen the skirting board from the wall. be careful not to damage the wall or the board itself. once the board is loosened, use a crowbar or similar tool to slowly pry it away from the wall. again, be careful not to damage anything. Carefully press the skirting board into place, ensuring it is level and flush with the wall. secure the skirting board by driving nails at an angle (toe nailing) through the top edge of the board and into the wall studs. use a nail gun or a hammer and nail set for this step. space the nails at intervals of about 12 16 inches (30 40 cm) apart. Step 6. check for any plugs, cables or other points of interest above the skirting board. it’s important to ensure you put nails either side of any areas like these, so the nails don’t damage cables or electrical fittings. if you’re at all unsure, switch off your electrical system before applying the nails.
Comments are closed.