How To Install A Shower Or Tub Faucet
![Hooking Up a Shower or Tub faucet how To Install A New Bathroom Diy Hooking Up a Shower or Tub faucet how To Install A New Bathroom Diy](https://images.meredith.com/diy/images/2009/02/p_SCP_190_02.jpg)
Hooking Up A Shower Or Tub Faucet How To Install A New Bathroom Diy Add hammer arresters. anchor the faucet according to manufacturer's directions. once you're sure of the connections, sweat all the fittings. start at the faucet, then move on to the shower arm and spout connections. run 1 2 inch pipe up to the shower arm and down to the spout; attach drop ear elbows at both spots. This video will walk you through the entire process and give you the step by step instructions you need for a successful installation. shop all shower faucets. share: bath. currently loaded videos are 1 through 15 of 51 total videos. 1 15 of 51. 1:25.
![how To Install A Shower Or Tub Faucet Storables how To Install A Shower Or Tub Faucet Storables](https://storables.com/wp-content/uploads/2023/09/how-to-install-a-shower-or-tub-faucet-1693531355.jpeg)
How To Install A Shower Or Tub Faucet Storables Peel the end of your plumber’s tape back a couple of inches. with the new valve in one hand, hold the threaded base pointing to your other hand. place the loose end of the plumber’s tape over the threads and secure it with your thumb, then wrap tightly around the threads clockwise for three complete wraps. Step 5: remove the old shower valve. along with the valve you’ll find three copper pipes. one goes up to the shower head and the other two to the hot and cold lines. cut the pipes with a tube cutter. once the pipes are cut, use a reciprocating saw to detach the stringer from the studs. Use the wire brush to clean the inside of the fitting. apply a light coating of solder paste or flux to the inside of the valve fittings, and to the cleaned end of the copper pipe. insert the end of the pipe all the way into the adapter. use a torch to heat up the middle of the fitting. If you want to help support shannon to produce more videos like this, visit house improvements donateshannon from house improveme.
![Learn How To Properly Hook Up a Shower or Tub faucet While Ensuring Learn How To Properly Hook Up a Shower or Tub faucet While Ensuring](https://i.pinimg.com/originals/ea/3b/4b/ea3b4b6ee9fae4f9a15dbe300a9beea8.jpg)
Learn How To Properly Hook Up A Shower Or Tub Faucet While Ensuring Use the wire brush to clean the inside of the fitting. apply a light coating of solder paste or flux to the inside of the valve fittings, and to the cleaned end of the copper pipe. insert the end of the pipe all the way into the adapter. use a torch to heat up the middle of the fitting. If you want to help support shannon to produce more videos like this, visit house improvements donateshannon from house improveme. To change a bathtub cartridge, begin by removing the handle as described in step 1. remove the screws holding the escutcheon plate in place and slide out the escutcheon. remove the retaining clip that holds the cartridge in place with a screwdriver. remove the cartridge with pliers. Mark the cutout using the cover’s paper template and a crayon. photo 1a: tile cutting bit. a tile bit in a rotary tool cuts through most ceramic tile. photo 2: install the new valve. solder in the new valve. use the paper template to make sure the valve is centered in the cutout. photo 3: mount the cover plate.
![Delta shower faucet Quick install Guide Youtube Delta shower faucet Quick install Guide Youtube](https://ytimg.googleusercontent.com/vi/hGI9F-lY5xk/maxresdefault.jpg)
Delta Shower Faucet Quick Install Guide Youtube To change a bathtub cartridge, begin by removing the handle as described in step 1. remove the screws holding the escutcheon plate in place and slide out the escutcheon. remove the retaining clip that holds the cartridge in place with a screwdriver. remove the cartridge with pliers. Mark the cutout using the cover’s paper template and a crayon. photo 1a: tile cutting bit. a tile bit in a rotary tool cuts through most ceramic tile. photo 2: install the new valve. solder in the new valve. use the paper template to make sure the valve is centered in the cutout. photo 3: mount the cover plate.
Comments are closed.