How To Install Roof Decking Howtospecialist How To Build Step By
![how To Install Roof Decking Howtospecialist How To Build Step By how To Install Roof Decking Howtospecialist How To Build Step By](https://www.howtospecialist.com/wp-content/uploads/2013/01/Fitting-the-roof-decking.jpg)
How To Install Roof Decking Howtospecialist How To Build Step By Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. secure the tar paper to the plywood sheets with roofing staples. in addition, cut a 12″ piece for the top ridge. fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under. Align the walls properly and plumb them with a spirit level, before drilling pilot holes trough the plans and inserting 3 1 2” into the joists. secure the frames into place with braces, util you fit the rest of the walls. workshop frame. install the rest of the walls, placing them as in the image.
![how To Install Roof Decking Howtospecialist How To Build Step By how To Install Roof Decking Howtospecialist How To Build Step By](https://www.howtospecialist.com/wp-content/uploads/2013/01/Installing-a-shed-roofing-1024x604.jpg)
How To Install Roof Decking Howtospecialist How To Build Step By Fitting the roof sheets. fit the 3 4″ plywood sheets to the top of the shed roof. align the edges flush and insert 1 5 8″ screws, every 8″ along the rafters. roof trims. fit the 2×6 trims to the sides of the roof. lock them into place tightly with 2 1 2″ screws. fit the 1×6 trims to the front and back of the shed roof. 10. install plywood roof decking. at this stage, your lean to shed roof is fully framed. the last step in the lean to shed roof framing process is to install the plywood roof sheathing. if you planned out your rafter spacing appropriately in the previous steps, your plywood decking layout should ensure that the edges of each piece of plywood. Installing a porch roof over an existing deck is usually not recommended unless the deck was originally designed to support a future porch. typical decks are designed to support 55 psf (lbs per square foot). porch decks require 25 additional psf for roof loads for a total of 80 psf. as a result, most decks have inadequate footings to support a. Dig down beneath the frost line and install 10 inch sonotubes (reinforced cardboard tubes) to hold the posts. the frost line varies depending on the climate where you live. it can be as deep as 72 inches and as shallow as six inches. fill the holes with concrete and top it off with 6×6 inch post brackets.
![how To Install Roof Decking Howtospecialist How To Build Step By how To Install Roof Decking Howtospecialist How To Build Step By](https://www.howtospecialist.com/wp-content/uploads/2013/01/Installing-the-overhangs.jpg)
How To Install Roof Decking Howtospecialist How To Build Step By Installing a porch roof over an existing deck is usually not recommended unless the deck was originally designed to support a future porch. typical decks are designed to support 55 psf (lbs per square foot). porch decks require 25 additional psf for roof loads for a total of 80 psf. as a result, most decks have inadequate footings to support a. Dig down beneath the frost line and install 10 inch sonotubes (reinforced cardboard tubes) to hold the posts. the frost line varies depending on the climate where you live. it can be as deep as 72 inches and as shallow as six inches. fill the holes with concrete and top it off with 6×6 inch post brackets. Space staples approximately 12 inches apart. work your way from the eave to the peak, laying the courses horizontally with the upper courses overlapping the lower ones by at least two inches. when you need two pieces of paper in the same row, overlap their seams by at least six inches. use a utility knife for cutting. The first layer on top of the plywood or osb roof deck is underlayment. for this, we chose a self healing ice and water membrane to protect the shallow pitched roof deck. the tricky part in laying the underlayment is keeping it flat and wrinkle free. unroll the underlayment across the roof while removing the bottom half of the adhesive backing.
Comments are closed.