How To Plumb A Bathroom With One Vent Two Sinks Toilet And Tub Shower
![how To Plumb a Bathroom with One vent two sinks toilet how To Plumb a Bathroom with One vent two sinks toilet](https://ytimg.googleusercontent.com/vi/dir9x5RShG4/maxresdefault.jpg)
How To Plumb A Bathroom With One Vent Two Sinks Toilet Follow along with our plumbing and hvac manager marlin sundberg as he goes through the step by step process of plumbing a horizontal bathroom group with one. The most common configuration is to feed 2" pvc down from the ceiling within the wall behind the toilet. the vent pipe connects into the toilet drain pipe. the sink drain pipe and the tub shower drain pipe are vented with 1.5" pipe that branches off from the 2" pvc mainline.
![bathroom toilet vents bathroom toilet vents](https://www.bhg.com/thmb/2T2sBYz8RyPUcsuY1JecdtE4tcI=/1500x0/filters:no_upscale():max_bytes(150000):strip_icc()/venting-sink-toilet-bathtub-diagram-6fe98bed-a3fbe89aa95f45b0a98754e849ad13fa.jpg)
Bathroom Toilet Vents Here’s how to connect the plumbing under your bathroom sink. you will need a 1.5″ trap adapter and a 1.5″ plastic tubing p trap (sometimes called trim trap). trim trap kits come with two different sizes of washers. you’ll use the 1.5″ x 1.25″ slip joint washer to connect the p trap to the lav’s 1.25″ waste outlet. Grab your free cheat sheet:1. *** 2 free bathroom plumbing plans: hammerpedia.co diagram2. *** free toilet venting guide: hammerpedia v. When space beneath a toilet is not a problem, use a setup such as the one shown in “venting a toilet,” in which a 2 in. vent pipe rises vertically from a 3 by 2 combo, while the 3 in. drain continues on to the house main. the 3 in. diameter toilet drain allows the vent to be as far as 6 ft. from the fixture, as indicated in the table. Measure the distance from the toilet drainpipe to the roofline, adding a few extra inches to accommodate adjustments. use a saw to cut the vent pipe. 3. create the roof opening. create a hole at your chosen exit point on the roof; make sure it’s a smidge larger than the pipe’s diameter.
![How To vent A toilet sink And shower How To vent A shower Drain How To vent A toilet sink And shower How To vent A shower Drain](https://images0.plumbersstock.com/content/how-to-vent-toilet-shower-sink-700x425-min.jpg)
How To Vent A Toilet Sink And Shower How To Vent A Shower Drain When space beneath a toilet is not a problem, use a setup such as the one shown in “venting a toilet,” in which a 2 in. vent pipe rises vertically from a 3 by 2 combo, while the 3 in. drain continues on to the house main. the 3 in. diameter toilet drain allows the vent to be as far as 6 ft. from the fixture, as indicated in the table. Measure the distance from the toilet drainpipe to the roofline, adding a few extra inches to accommodate adjustments. use a saw to cut the vent pipe. 3. create the roof opening. create a hole at your chosen exit point on the roof; make sure it’s a smidge larger than the pipe’s diameter. Install a sanitary tee. install a sanitary tee facing into the room for the sink trap. the ideal height is usually 18 inches above the finished floor, but check your sink instructions to be sure. cement a 1¼ inch trap adapter into the tee. install a piece of 1x6 blocking and anchor the pipe with a strap. Carefully lift the toilet into place, so it rests on the flange with the bolts through the pre drilled holes. add washers and nuts and tighten, so it’s held in place. 5. level the toilet. check to make sure the toilet is level and put washers underneath either side if needed.
![How To vent plumb A toilet 1 Easy Pattern вђ Artofit How To vent plumb A toilet 1 Easy Pattern вђ Artofit](https://i.pinimg.com/originals/8c/01/04/8c0104029617877a2de31994cadaa417.jpg)
How To Vent Plumb A Toilet 1 Easy Pattern вђ Artofit Install a sanitary tee. install a sanitary tee facing into the room for the sink trap. the ideal height is usually 18 inches above the finished floor, but check your sink instructions to be sure. cement a 1¼ inch trap adapter into the tee. install a piece of 1x6 blocking and anchor the pipe with a strap. Carefully lift the toilet into place, so it rests on the flange with the bolts through the pre drilled holes. add washers and nuts and tighten, so it’s held in place. 5. level the toilet. check to make sure the toilet is level and put washers underneath either side if needed.
Comments are closed.