I Just Bought This Boat And Astro Black Max 150 Transom Issue 9 28 21
![i Just bought this Boat and Astro black max 150 transo i Just bought this Boat and Astro black max 150 transo](https://ytimg.googleusercontent.com/vi/4ADt5Hw4_F4/maxresdefault.jpg?sqp=-oaymwEmCIAKENAF8quKqQMa8AEB-AHUBoAC4AOKAgwIABABGGUgZShlMA8=&rs=AOn4CLDeTNpfPtg05MIo0PtYxOU-4OsNTg)
I Just Bought This Boat And Astro Black Max 150 Transo This was actually pretty sad. the customer drove out of state to purchase this boat. the seller stated he did not have time to take it to the lake for a lake. 47. may 3, 2010. #4. re: mercury black max 150. the 135 150 motors will run about 145 150 at idle and 130 140 at cruise in 60 deg water. one typical mistake is to leave the slinger washer off. this is the one that looks like a garden hose washer and slides over the drive shaft ending up on top of the water pump housing.
![Our boat Could Have Sank Major transom issue Youtube Our boat Could Have Sank Major transom issue Youtube](https://ytimg.googleusercontent.com/vi/j5g20KBub08/maxresdefault.jpg)
Our Boat Could Have Sank Major Transom Issue Youtube "just recently bought a boat w "just recently bought a boat with a mercury blackmax 150 and i have a few questions, new to boat ownership 1. what year is this outboat serial number tag says 6617130? 2. motor is slightly difficult to start hot or cold? 3. water pressure gauge read 1 2 psi at idle and 13 15 psi at full throttle, nothing is coming. There are a few best practices to treat your transom wood: wait for the ideal temperature —between 50 and 70 degrees fahrenheit. at about 70 degrees, the applied git rot will solidify overnight, boosting the wood’s strength. inject the git rot into the wood’s end grain whenever possible. think of git rot like blood moving through. Customer: 85 black max 150 xr2 starts and runs fine on muffs in the driveway get to the lake launch the boat it starts sputters and mechanic's assistant: sometimes boat issues seem like they'll be really complicated, but end up being easy to fix. the marine mechanic i'm going to connect you with knows all the tricks and shortcuts. The lower unit oil, every year. plugs 2 3 years. a couple of bucks spent each year will prevent poor performance or expensive repairs. pull the prop off now and then and check for braided line wrapped around the prop shaft. a well maintained mercury 150 will last for many years.
![88 91 Mercury Xr4 150 Hp black max Outboard For Sale In 45 Off 88 91 Mercury Xr4 150 Hp black max Outboard For Sale In 45 Off](https://cimg5.ibsrv.net/gimg/www.thehulltruth.com-vbulletin/2000x1504/b1f7ebf2_b911_4db0_9338_34a1640eb8f2_c5f272040f2cb645bd4c7315eb6ed64333dbf76d.jpeg)
88 91 Mercury Xr4 150 Hp Black Max Outboard For Sale In 45 Off Customer: 85 black max 150 xr2 starts and runs fine on muffs in the driveway get to the lake launch the boat it starts sputters and mechanic's assistant: sometimes boat issues seem like they'll be really complicated, but end up being easy to fix. the marine mechanic i'm going to connect you with knows all the tricks and shortcuts. The lower unit oil, every year. plugs 2 3 years. a couple of bucks spent each year will prevent poor performance or expensive repairs. pull the prop off now and then and check for braided line wrapped around the prop shaft. a well maintained mercury 150 will last for many years. The past 4 transoms that i did were two sheets of exterior grade plywood. laminated together, properly sealed, and a 1 8" aluminum plate bonded to that. another method would be to laminate 3 layers of 1 2" plywood together. when multiple layers are glued together, it becomes much stronger than just two. Check to coast guard capacity plate in the boat and see how much weight it can handle. as suggested earlier, launch the boat and put some weight right in front of the motor, don't spread it across the stern. two batteries is a good idea. run the boat and see how it sits in the water and how often you take water over the transom.
![1998 astro 1850 Dcx Fairfield Ohio Boats 1998 astro 1850 Dcx Fairfield Ohio Boats](https://images.boats.com/resize/1/36/82/8763682_0_220320231754_1.jpg?t=1679532772000)
1998 Astro 1850 Dcx Fairfield Ohio Boats The past 4 transoms that i did were two sheets of exterior grade plywood. laminated together, properly sealed, and a 1 8" aluminum plate bonded to that. another method would be to laminate 3 layers of 1 2" plywood together. when multiple layers are glued together, it becomes much stronger than just two. Check to coast guard capacity plate in the boat and see how much weight it can handle. as suggested earlier, launch the boat and put some weight right in front of the motor, don't spread it across the stern. two batteries is a good idea. run the boat and see how it sits in the water and how often you take water over the transom.
Comments are closed.