Safety Pin Bracelet How To Make In 27 Ways Guide Patterns Diy safety pin bracelet with brooch. the large beads and safety pins inserted with the smaller beads are alternately threaded to the string followed by weaving a long strip of soft fabric around the bracelet. the finishing is done with a glossy brooch. safety pin bracelet tutorial. chic safety pin bracelet. For size 0, that is 7 pins. make another pin with 7 pins attached to its fixed side. once you have two sets completed, attach them together by threading the pin from one set through the holes on the ends of the 7 pins of the second set. close the pin. continue repeating these steps until you have a bracelet that fits your wrist.
Safety Pin Bracelet How To Make In 27 Ways Guide Patterns Make sure that you weave between the beads, with two beads on top and two on the bottom. [17] weave back and forth across the bracelet until the space between the beads is filled. 11. weave across the back of the safety pins. once the front of the bracelet is filled, weave the fabric through the back of the bracelet. Step 2: sringing the pins. cut two 12 inch pieces of elastic. tie one string onto one end of the first beaded safety pin, leaving a tail for later. (like in the picture) tie the other string onto the other end of the pin. string an empty safety pin flipped onto the two strings. look at the pictures below for help. Instructions. put some glue on a paper plate, about the size of a quarter. open a safety pin and thread as many seed beads on as you can, leaving enough room to close the pin. dip toothpick into the glue and use it to add a dot of glue to the end of the pin, then fasten. It is up to you how many beads you want to add. 3. combine all safety pins. to combine all safety pins, use the round beading elastic. begin by threading the elastic string through the first safety pin. insert the safety pins one by one. thread the next safety pin through the first pin, and so on. 4. tie a knot.
Safety Pin Bracelet How To Make In 27 Ways Guide Patterns Instructions. put some glue on a paper plate, about the size of a quarter. open a safety pin and thread as many seed beads on as you can, leaving enough room to close the pin. dip toothpick into the glue and use it to add a dot of glue to the end of the pin, then fasten. It is up to you how many beads you want to add. 3. combine all safety pins. to combine all safety pins, use the round beading elastic. begin by threading the elastic string through the first safety pin. insert the safety pins one by one. thread the next safety pin through the first pin, and so on. 4. tie a knot. Open one of the safety pins, and thread beads onto the open prong, leaving enough space to refasten the pin. repeat the process until all of the safety pins have been beaded. 2. glue the pin so that it wouldn’t open when you’re wearing it. 3. next, cut two 12” pieces of elastic cord. 4. thread one of the cords through the hole in the top. Triple knot 1 end of each of the two pieces, place your knot about 1 2 inch from the end, so you have a small tail of elastic, you’ll need this for securing the two ends of the bracelet to each other. you’ll knot the other opposing end after you’ve strung them. put aside. 2. start beading your safety pins, leaving enough space at the top.
Safety Pin Bracelet How To Make In 27 Ways Guide Patterns Open one of the safety pins, and thread beads onto the open prong, leaving enough space to refasten the pin. repeat the process until all of the safety pins have been beaded. 2. glue the pin so that it wouldn’t open when you’re wearing it. 3. next, cut two 12” pieces of elastic cord. 4. thread one of the cords through the hole in the top. Triple knot 1 end of each of the two pieces, place your knot about 1 2 inch from the end, so you have a small tail of elastic, you’ll need this for securing the two ends of the bracelet to each other. you’ll knot the other opposing end after you’ve strung them. put aside. 2. start beading your safety pins, leaving enough space at the top.
Comments are closed.