Transmission Line Removal Question For Complete Flush Ford Truck
![transmission Line Removal Question For Complete Flush Ford Truck transmission Line Removal Question For Complete Flush Ford Truck](https://i1187.photobucket.com/albums/z390/SuperMuncheese/IMG_20140630_164105.jpg)
Transmission Line Removal Question For Complete Flush Ford Truck 3.8 & 4.2l v6 transmission line removal question for complete flush do i just pull this out (with force), after i remove the white cap? it doesnt want to come out very easily. what i want to do is have the return line, which would be the cooler line, in a bucket filled with new transmission oil. and have the. Simply drain the fluid and replace the filter should be good enough. if you want to flush, just simply add another drive cycle to get the transmission hot and circulate the oil and drain and refill. reply like. # 3. 09 10 2023, 08:49 pm. mark kovalsky.
![2007 ford F150 transmission line removal 2007 ford F150 transmission line removal](https://ytimg.googleusercontent.com/vi/k5r59jDnSUY/maxresdefault.jpg)
2007 Ford F150 Transmission Line Removal Location: middle tn. the torque shift tranny has an internal t stat and to do a complete flush you need a heated flush machine. internal t stat is approximately 170 degrees. what i did when i had mine was to drain the pan every oil change, 5000 miles, and put in 8 quarts of new fluid. mercon sp or lv only. It's usually between 10 to 20 psi at the cooler. older transmissions had 10 20 psi in the cooler lines. the 5r110w had about 60 psi. i would expect the 6r140 is at least 60 psi, but i have no hard data on that. mark. former ford automatic transmission engineer. Two people make this task easier. remove the drain plug and allow the tc to drain. it will take about 30 minutes to completely drain. finally, remove the 14, 10mm transmission pan bolts and lower the pan down. notice, little or no atf is in the pan. drop the filter into the pan and discard. I put it back together and have ran 20 quarts through it (dumping into jugs through line that goes into rad.) and it is still milky , waiting for some more from rockauto , have new radiator and hoses to go back in if it ever clears . general f150 discussion 2000 f150 transmission flush so i'm in the process of cleaning coolant out of my.
![transmission Line Removal Question For Complete Flush Ford Truck transmission Line Removal Question For Complete Flush Ford Truck](https://i1187.photobucket.com/albums/z390/SuperMuncheese/tranline.jpg)
Transmission Line Removal Question For Complete Flush Ford Truck Two people make this task easier. remove the drain plug and allow the tc to drain. it will take about 30 minutes to completely drain. finally, remove the 14, 10mm transmission pan bolts and lower the pan down. notice, little or no atf is in the pan. drop the filter into the pan and discard. I put it back together and have ran 20 quarts through it (dumping into jugs through line that goes into rad.) and it is still milky , waiting for some more from rockauto , have new radiator and hoses to go back in if it ever clears . general f150 discussion 2000 f150 transmission flush so i'm in the process of cleaning coolant out of my. Take it to a good transmission shop that uses a low pressure flush process. its been discussed back and forth as to flushing or not with a high mileage transmission for its first flush. i've had 3 trucks purchased, all with over 100k when purchased. my local transmission shop inspects the truck (pan drop) before they recommend a flush. 8) detach transmission oil cooler lines. detach the two transmission oil cooler lines at the transmission.line wrench. tip: it is best to use a line wrench when loosening and tightening the oil cooler lines. also, when pulling the lines out, be careful not to lose the thin metal washers. the fittings will leak if these washers are not replaced.
Comments are closed.