Wood Stairs On A Concrete Porch
![wood porch Over concrete Steps Google Search In 2020 Front porch wood porch Over concrete Steps Google Search In 2020 Front porch](https://i.pinimg.com/736x/8c/8b/2d/8c8b2dd2a0a635eb07f8e2389111f152.jpg)
Wood Porch Over Concrete Steps Google Search In 2020 Front Porch How to calculate, lay out, saw, and attach a set of treated pine steps to a concrete porch. The process. to begin this project, we purchased a couple of 4 step stair stringers to put on the outside of the old steps. to make our stairs wider, we placed them about a foot out on either side of the stairs. we screwed four 1″ by 8″ treated yellow pine boards into the front of the stringers to create the new wood risers.
![How To Cover concrete Steps With wood concrete Front porch concrete How To Cover concrete Steps With wood concrete Front porch concrete](https://i.pinimg.com/originals/97/d3/19/97d3198632fe63f367b74af27d295e30.jpg)
How To Cover Concrete Steps With Wood Concrete Front Porch Concrete Use your jigsaw. notch out the bottom front of the center stair stringers to accept a 2x4 base plate. make sure your stringers are level. fasten the base plate to the stair stringers with screws. locked in place. use a hammer and drill to install 1 2" x 3" sleeve anchors through the base plate into the concrete pad. find the best deck builders. Attaching the stairs to the porch. set the stringer assembly against the porch and secure it with several 8 inch structural screws. use a hammer drill to create pilot holes through the bottom 2 by 6 and into the concrete walkway. fasten the bottom of the staircase to the walkway using 3 inch masonry screws. 1) diy pallet wood letters. one way to decorate concrete steps to look nice is to add pallet wood letters to them. use this tutorial to make a letter with your last initial, or even your full set of initials, and place it on the stairs. the pallet wood will create a rustic look that will match the bare concrete while making it look nice. Hi! in this video i explain how i transformed my uneven concrete stairs with wood decking and 2x4s to prepare for a deck i will be building shortly.
![concrete Front porch Step Designs concrete Front porch Step Designs](https://www.randolphsunoco.com/wp-content/uploads/2018/11/best-paint-for-concrete-porches.jpg)
Concrete Front Porch Step Designs 1) diy pallet wood letters. one way to decorate concrete steps to look nice is to add pallet wood letters to them. use this tutorial to make a letter with your last initial, or even your full set of initials, and place it on the stairs. the pallet wood will create a rustic look that will match the bare concrete while making it look nice. Hi! in this video i explain how i transformed my uneven concrete stairs with wood decking and 2x4s to prepare for a deck i will be building shortly. Cut angled braces and fasten them to the side forms at the front edge of each step. then drive 2x4 stakes at the bottom of the braces. plumb the side forms and fasten the braces to the stakes. to keep the riser forms from bowing, drive a 2x4 stake 18 inches or deeper into the ground in front of the steps. The standard way to build steps is to cut stringers out of 2″ x 10″ or 2″ x 12″ lumber, and to secure those to the deck or porch. this is a very informative video that describes that standard method. i chose not to use that method. instead, i chose to build a series of modified boxes that stack one on top of the other.
![Pin On Landscaping Ideas Pin On Landscaping Ideas](https://i.pinimg.com/originals/ba/31/79/ba3179462ed9f166e8e42c3c40628ef8.jpg)
Pin On Landscaping Ideas Cut angled braces and fasten them to the side forms at the front edge of each step. then drive 2x4 stakes at the bottom of the braces. plumb the side forms and fasten the braces to the stakes. to keep the riser forms from bowing, drive a 2x4 stake 18 inches or deeper into the ground in front of the steps. The standard way to build steps is to cut stringers out of 2″ x 10″ or 2″ x 12″ lumber, and to secure those to the deck or porch. this is a very informative video that describes that standard method. i chose not to use that method. instead, i chose to build a series of modified boxes that stack one on top of the other.
Comments are closed.